A 3.78 L tub of Titebond TitePatch Textured Knife Grade compound
Titebond TitePatch tub and illustration of non-structural crack repair
Illustration of Titebond TitePatch adhesion and flexibility
Illustration of painting Titebond TitePatch after 30 minutes with a brush
Illustration of Titebond TitePatch for interior and exterior use

Titebond TitePatch Textured – textured elastomeric compound for interior and exterior cracks and gaps

€18.79 - €57.88

Titebond TitePatch – textured elastomeric compound for repairing non-structural cracks and gaps. For interior and exterior use: fills and seals cracks in concrete, masonry, plaster and other compatible surfaces.

Strong adhesion and a flexible repair. Forms a strong, durable layer resistant to moisture, frost and vibration, acting as a flexible patch. Suitable for concrete, masonry, plaster, wood, brick, PVC, aluminium and galvanised steel.

Choose the application method: brush grade or knife grade. The brush-grade formulation is convenient for fine, hairline or thread-width cracks. Knife grade can also fill larger gaps. Both versions produce a textured surface that can be painted with water-based latex or acrylic paint after 30-60 min., once sufficiently dry.

Surface finish: textured · Application method: brush grade or knife grade.
Pack sizes: 946 ml and 3.78 l · Applications: for interior and exterior use.
Important: for non-structural cracks; cannot be sanded after drying.
More about the compound and its applicationCollapse additional information

Brush grade or knife grade?

Brush Grade – for covering fine surface cracks with a thin elastomeric layer. Knife Grade – for filling gaps and smoothing with a filling knife or trowel. After choosing the application method, select the required pack size.

Flexible layer over the crack

Spread the compound approximately 5 cm either side of the centre of the crack, feathering the edges. This creates a wider elastomeric layer that distributes stresses more effectively. Sealing fine cracks in the building envelope helps restrict wind and moisture ingress; the building's energy rating depends on the complete design.

Preparation and painting

Surfaces must be clean and free from substances that impair adhesion. Allow new concrete to cure for 30 days. Smooth the compound while wet: it cannot be sanded after drying. Paint only when dry to the touch, usually after 30-60 min., although the time depends on conditions. Test compatibility with other paint types.

Application limitations

Do not use for structural cracks, continuously submerged areas or below the waterline. During application, the air, compound and substrate temperatures must be above +4.5 °C. Do not apply outdoors if rain is expected within 12 hours. Detailed application steps and documents for each formulation are provided below.

SKU: N/A Category: Tags: , , , , , , , , , , , , , , , , , , , , , , , ,

ThumbnailSKUQuantityWeightPriceQuantity 
A 3.78 L tub of Titebond TitePatch Textured Knife Grade compound
5375 TEXTURED KNIFE GRADE946 ml/1.36 kg, knife grade037083053753€18.79
A 3.78 L tub of Titebond TitePatch Textured Knife Grade compound
5365 TEXTURED BRUSH GRADE946 ml/1.21 kg, brush grade037083053654€18.79
A 3.78 L tub of Titebond TitePatch Textured Knife Grade compound
5376 TEXTURED KNIFE GRADE3.78 l/5.44 kg, knife grade037083053760€57.88
A 3.78 L tub of Titebond TitePatch Textured Knife Grade compound
5366 TEXTURED BRUSH GRADE3.78 l/4.84 kg, brush grade037083053661€57.88

Compatible surfaces

Concrete, masonry, plaster, wood, brick, PVC, aluminium and galvanised steel.

Four TitePatch formulations

  • TitePatch Smooth Brush Grade – smooth brush-applied compound for hairline cracksView PDFDownload PDF
  • TitePatch Smooth Knife Grade – smooth knife-applied compound for small and larger gapsView PDFDownload PDF
  • TitePatch Textured Brush Grade – textured brush-applied compound for hairline cracksView PDFDownload PDF
  • TitePatch Textured Knife Grade – textured knife-applied compound for small and larger gapsView PDFDownload PDF

The brush-grade compound is suitable for fine, hairline or thread-width cracks in interior and exterior walls and ceilings. Sealing fine cracks helps restrict wind and moisture ingress. In A+ energy-rated buildings, product suitability must be assessed as part of the complete airtightness solution.

Preparation for both application methods

Surfaces must be clean and free from materials that impair adhesion. Allow new concrete to cure for 30 days. The user is responsible for proper substrate preparation and checking product suitability for the specific surface.

Brush-grade compound

  1. Apply to fine, hairline or thread-width cracks with a brush or filling knife. For a smoother finish, tool along the full length of the crack with a filling knife, keeping the crack centred beneath the blade.
  2. Spread a thin layer approximately 5 cm either side of the centre of the crack. This wider elastomeric layer acts as a patch and distributes stresses more effectively.

Knife-grade compound: cracks up to 0.8 mm

  1. Apply a wet layer up to 1.5 mm thick using a filling knife or trowel.
  2. Spread the compound approximately 5 cm either side of the centre of the crack. Feather the edges into the surface to form a wider elastomeric patch.

Knife-grade compound: cracks wider than 0.8 mm

  1. Mechanically widen the crack to approximately 6 mm wide and 6 mm deep.
  2. Fill the crack and leave a slightly raised layer above it to compensate for shrinkage as the compound dries.
  3. Allow to dry for at least 4 hours. Apply an additional layer approximately 1.5 mm thick, extending approximately 5 cm either side of the centre of the crack and feathering the edges. This creates a wider elastomeric patch with greater resistance to stress.
Quantity

946 ml/1.36 kg, knife grade, 946 ml/1.21 kg, brush grade, 3.78 L/5.44 kg, knife grade, 3.78 L/4.84 kg, brush grade

Composition: latex.
Colours: white and sand; see the documentation for the specific variant.
Freeze/thaw stability: stable.
VOC: 50 g/l (< 0,15 %).
Flash point: none.
Approximate coverage: about 24 linear metres per 3.78 L or 6 linear metres per 946 ml, applied at 1.5 mm thick and 10 cm wide.

Pack sizes and weights:
Brush grade: 946 ml / 1.21 kg or 3.78 L / 4.84 kg.
Knife grade: 946 ml / 1.36 kg or 3.78 L / 5.44 kg.

Application temperature: from +4.5°C to +49°C.
Service temperature: from –18°C to +71°C.

Tool cleaning: clean tools with soapy water before the compound dries. Wash hands with soap and water after use.

Application instructions: detailed brush and knife application steps are provided under Description. Choose the PDF for the formulation you are using.

Do not use to repair structural cracks, in continuously submerged areas or below the waterline. The dried compound cannot be sanded.

Air, compound and surface temperatures must be above +4.5°C. Do not apply if rain is expected within the next 12 hours. Drying depends on ambient conditions, temperature and humidity.

Paint only once the compound is touch-dry. Use water-based latex paints without plasticisers. Painting may be possible from 30 minutes, usually after 30–60 minutes, depending on conditions. Test compatibility with other paint types.

For best results, store in a warm, dry place at no more than +24°C. For questions, use the supplier contacts at titebond.lt. Liability is limited to product replacement.

Read the product safety data sheet before use. Keep out of reach of children.

APRAŠYMAS TitePatch™ Textured Brush Grade - Tekstūruotos teptukui skirtos formulės mišinys

Download

APRAŠYMAS TitePatch™ Textured Knife Grade - Tekstūruotos glaistyklei skirtos formulės mišinys

Download

Related products

0
    0
    Basket
    Your basket is emptyGo to shop
    Continue shopping