Titebond II Premium Dark – tamsiai rudi, vandeniui atspar\u016bs D3 medienos klijai tamsiai medienai, bald\u0173 gamybai ir remontui, vidaus bei lauko darbams.<\/p>\n
\u201eTitebond II Dark\u201c – rudi, vandeniui atspar\u016bs D3 medienos klijai vidaus ir lauko darbams. Tai tamsiai rudos spalvos \u201eTitebond II Premium\u201c versija, skirta tamsiai medienai, bald\u0173 gamybai ir remontui. Ruda sukiet\u0117jusi si\u016bl\u0117 geriau dera su rie\u0161utmed\u017eiu, raudonmed\u017eiu, vy\u0161nia ir kitomis tamsesn\u0117mis medienos r\u016b\u0161imis.<\/p>\n
\u012esp\u016bdingas klij\u0173 si\u016bl\u0117s stipris – apie 253,1 kg\/cm\u00b2.<\/strong> In the manufacturer's ASTM D905 test on hard maple joints at room temperature, Titebond II Dark achieved a shear strength of 3600 psi (approximately 24.8 MPa).<\/p>\n Shake the container thoroughly before use to ensure a uniform consistency.<\/strong><\/p>\n Bond strength:<\/strong> 253,10 kg\/cm\u00b2* Colour and applications.<\/strong> Skysti klijai yra \u0161viesiai rudi, sukiet\u0117jusi si\u016bl\u0117 – ruda. Klijai tinka medienai, medienos plau\u0161o ir dro\u017eli\u0173 plok\u0161t\u0117ms, odai, audiniui bei daugeliui kit\u0173 por\u0117t\u0173 med\u017eiag\u0173. Stiprus pradinis sukibimas ir greitas stingimas palengvina detali\u0173 surinkim\u0105 bei padeda sutrumpinti suspaudimo laik\u0105.<\/p>\n Water resistance.<\/strong> Titebond II Dark meets ANSI Type II water-resistance test requirements and is suitable for interior and exterior wood products.<\/p>\n Machining and finishing.<\/strong> The cured glue line sands easily and is suitable for subsequent finishing. For an even finish, remove glue residue from visible surfaces: wipe uncured glue with water or a damp cloth, and scrape or sand off cured glue. Suitable for radio-frequency (R-F) bonding systems.<\/p>\n Food contact.<\/strong> Titebond II Dark does not have manufacturer approval for indirect food contact under FDA requirements.<\/p>\n Non-toxicity and safe use.<\/strong> Gamintojo bro\u0161i\u016broje \u201eTitebond II Dark\u201c \u012fvardijami kaip netoksi\u0161ki klijai. Jie atitinka ASTM D-4236 reikalavimus, gamintojo nurodomas LOJ kiekis – ma\u017eiau nei 4 g\/l. Prie\u0161 naudojim\u0105 perskaitykite saugos duomen\u0173 lap\u0105, venkite patekimo \u012f akis, nenurykite ir laikykite vaikams nepasiekiamoje vietoje.<\/p>\n Application limitations.<\/strong> Not intended for continuous immersion in water or use below the waterline. Its low pH may corrode metal surfaces, so test first where relevant. Check adhesion when bonding preservative-treated timber; consult the supplier about exotic or oily woods such as ip\u00e9 and teak. Protect from freezing. Shaking may help restore glue thickened by freezing, but check its condition before use.<\/p>\n Not intended for structural bonding of load-bearing building components.<\/strong> If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.<\/p>\n *Strength measured to ASTM D905, bonding maple to maple at approximately +21 \u00b0C (3600 psi). Assembly times are given at +21 \u00b0C and 50 % relative humidity. Actual results depend on the timber, surface preparation and bonding conditions.<\/small><\/p>\n Naudojimo pavyzd\u017eius rasite skiltyje \u201eVideo\u201c, o i\u0161samius techninius duomenis – prid\u0117tame lietuvi\u0161kame PDF.<\/p>","protected":false},"excerpt":{"rendered":"\n
Open assembly time:<\/strong> approximately 5 min.
Total assembly time:<\/strong> 10-15 min.
Application temperature:<\/strong> above +12.8 \u00b0C.<\/p>\n