Titebond II Premium – vandeniui atspar\u016bs D3 medienos klijai bald\u0173 gamybai, remontui ir stali\u0173 darbams viduje bei lauke.<\/p>\n
\u201eTitebond II Premium\u201c – vandeniui atspar\u016bs D3 medienos klijai vidaus ir lauko darbams. Skirti bald\u0173 gamybai ir remontui, lauko suolams, inkilams, pa\u0161to d\u0117\u017eut\u0117ms, vazon\u0173 d\u0117\u017e\u0117ms ir kitiems medienos gaminiams. Stiprus pradinis sukibimas ir greitas stingimas padeda tiksliai sujungti detales bei sutrumpinti j\u0173 suspaudimo laik\u0105.<\/p>\n
\u012esp\u016bdingas klij\u0173 si\u016bl\u0117s stipris – apie 263,7 kg\/cm\u00b2.<\/strong> In the manufacturer's ASTM D905 test on hard maple joints at room temperature, Titebond II Premium achieved a shear strength of 3750 psi (approximately 25.9 MPa).<\/p>\n Bond strength:<\/strong> 263,65 kg\/cm\u00b2* Water resistance and applications.<\/strong> Titebond II Premium meets ANSI Type II water-resistance test requirements. Suitable for interior and exterior wood products, including outdoor furniture, benches and bird boxes.<\/p>\n Machining and finishing.<\/strong> The cured glue line sands easily and is suitable for subsequent finishing. To achieve an even finish, remove glue residue from visible surfaces: wipe uncured glue with water or a damp cloth, and scrape or sand off cured glue.<\/p>\n Production and food contact.<\/strong> Suitable for radio-frequency (R-F) and hot-press bonding systems. The manufacturer states compliance with US FDA requirements for indirect food contact, such as wooden chopping boards.<\/p>\n Non-toxicity and safe use.<\/strong> Gamintojo bro\u0161i\u016broje \u201eTitebond II Premium\u201c \u012fvardijami kaip netoksi\u0161ki klijai. Klijai atitinka ASTM D-4236 reikalavimus. Gamintojo nurodomas LOJ kiekis – ma\u017eiau nei 4 g\/l. Nesukiet\u0117j\u0119 klijai nuvalomi vandeniu. Venkite patekimo \u012f akis ir ilgalaikio s\u0105ly\u010dio su oda: produktas gali dirginti akis ir od\u0105. Nenurykite, laikykite vaikams nepasiekiamoje vietoje ir laikykit\u0117s saugos duomen\u0173 lapo nurodym\u0173.<\/p>\n Application limitations.<\/strong> Not intended for continuous immersion in water or use below the waterline. Its low pH may corrode metal surfaces, so test first where relevant. Check adhesion when bonding preservative-treated timber; consult the supplier about exotic or oily woods such as ip\u00e9 and teak. Protect from freezing. Shaking may help restore glue thickened by freezing, but check its condition before use.<\/p>\n Not intended for structural bonding of load-bearing building components.<\/strong> If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.<\/p>\n *Strength measured to ASTM D905, bonding maple to maple at approximately +21 \u00b0C (3750 psi). Assembly times are given at +21 \u00b0C and 50 % relative humidity. Actual results depend on the timber, surface preparation and bonding conditions.<\/small><\/p>\n Naudojimo pavyzd\u017eius rasite skiltyje \u201eVideo\u201c, o i\u0161samius techninius duomenis – prid\u0117tame lietuvi\u0161kame PDF.<\/p>","protected":false},"excerpt":{"rendered":"\n
Open assembly time:<\/strong> 3-5 min.
Total assembly time:<\/strong> 10-15 min.
Application temperature:<\/strong> above +12.8 \u00b0C.<\/p>\n