Product properties and application

„Titebond Speed Set“ – greitai tvirtėjantys PVA medienos klijai vidaus darbams, baldų gamybai ir medinių detalių surinkimui. Balti klijai išdžiūvę tampa skaidrūs, o jų likučiai matomi apšvietus UV lempa, todėl juos lengviau pastebėti ir pašalinti prieš apdailą.

Įspūdingas klijų siūlės stipris – apie 293,7 kg/cm². In the manufacturer's ASTM D905 test on hard maple joints at room temperature, Titebond Speed Set achieved a shear strength of 4178 psi (approximately 28.8 MPa).

• ✓ Short clamping time
• ✓ Glue residue is visible under UV light
• ✓ Dries clear
• ✓ Easy to sand
• ✓ For furniture and interior work
• ✓ Water clean-up before curing

Shake the container thoroughly before use to ensure a uniform consistency.

Bond strength: 293,74 kg/cm²*
Open assembly time: 2-4 min.
Total assembly time: 8-10 min.
Application temperature: above +15 °C.

Fast assembly. High solids content and strong initial tack help improve productivity and shorten clamping time. Suitable for furniture making, joinery and bonding wooden components indoors.

Colour and UV inspection. This white glue dries clear. Glue traces become clearly visible under a UV lamp. Remove residue before painting, varnishing or oiling so it does not interfere with an even finish.

Machining and cleaning. Sukietėjusi klijų siūlė lengvai šlifuojama. Nesukietėjęs perteklius nuvalomas vandeniu ar drėgna šluoste, sukietėjęs – nuskutamas arba nušlifuojamas.

Application limitations. For interior use. Do not use outdoors or where significant moisture is likely. For exterior work, select Titebond II Premium or Titebond III Ultimate according to the application. Air, glue and wood temperatures must be above +15 °C.

Not intended for structural bonding of load-bearing building components. If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.

Storage and preparation. Protect from freezing. Stir thoroughly before use, or shake the bottle, to ensure a uniform consistency. Stir monthly during storage to reduce settling.

Non-toxicity and safe use. The manufacturer's technical data sheet describes Titebond Speed Set as non-toxic. Read the current Safety Data Sheet before use and follow its instructions. Keep out of children's reach.

*Bond strength measured to ASTM D905 on maple joints at approximately +21 °C: 4178 psi / 28.80 N/mm² / 293.74 kg/cm². Assembly times are given at +21 °C and 50 % relative humidity. Actual results depend on the timber, surface preparation and bonding conditions.

Naudojimo pavyzdžius rasite skiltyje „Video“, o išsamius techninius duomenis – pridėtame lietuviškame PDF.

Product properties and application

„Titebond Melamine Glue“ – klijai medienai, MDF ir medienos drožlių plokštėms su melamino, vinilo ar HPL paviršiais klijuoti. Skirti baldų gamybai ir tiksliam detalių surinkimui. At least one bonding surface must be porous.

Strong initial tack and precise assembly. Grabs quickly, while an open time of approximately 5 minutes allows components to be aligned. The thick consistency reduces runs and drips.

Patikimas melamino ir medienos drožlių plokštės sujungimas – apie 23,8 kg/cm². The manufacturer's ASTM D905 test recorded a strength of 339 psi (approximately 2.34 MPa). This result applies to the melamine-to-particleboard test specimen.

• ✓ For wood, MDF and particleboard
• ✓ For melamine, vinyl and HPL joints
• ✓ Strong initial grab
• ✓ Tiršti – mažiau nubėgimų
• ✓ Dries clear
• ✓ Water clean-up before curing

Shake the container thoroughly before use to ensure a uniform consistency.

Open assembly time: approximately 5 min.
Total assembly time: 10-15 min.
Application temperature: above +5 °C.
Coverage: 5-6 m²/l.

What is this glue designed for? Bonding porous wood, MDF and particleboard to melamine, vinyl or HPL surfaces. Suitable for furniture making, bonding trim and precise assembly.

Consistency and glue-line appearance. Higher viscosity reduces runs and drips. The white glue dries clear.

Application and cleaning. Spread the glue with the bottle nozzle, a roller or a brush. Remove uncured excess with water or a damp cloth. Scrape or sand off cured residue.

Application limitations. For interior use; not intended for outdoor conditions or continuous immersion in water. At least one bonding surface must be porous. Do not use when the glue or bonding surfaces are below +5 °C.

Not intended for structural bonding of load-bearing building components. If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.

Storage and preparation. Protect from freezing. Do not use glue that has frozen and turned into a gel. Shake the container before use to ensure a uniform consistency.

Safe use. Read the product label and current Safety Data Sheet before use, and follow their application and protection requirements. Keep out of children's reach. Contact our technical support if you have questions about application.

Assembly times are given at +21 °C and 50 % relative humidity. Actual working time depends on the materials, temperature, humidity and adhesive layer.

Naudojimo pavyzdžius rasite skiltyje „Video“, o medienos klijų pasirinkimo informaciją – pridėtame lietuviškame kataloge.

Product properties and application

„Titebond Quick & Thick Multi-Surface“ – universalūs, tiršti vandens pagrindo klijai medienai, keramikai, akmeniui, audiniui ir kitoms porėtoms medžiagoms. Skirti vidaus apdailai, baldų remontui ir smulkiems surinkimo darbams. At least one bonding surface must be porous.

Įspūdingas klijų siūlės stipris – apie 210,9 kg/cm². „Titebond Quick & Thick“ gamintojo ASTM D905 bandyme, bandant kietojo klevo jungtis kambario temperatūroje, pasiekė 3000 psi (apie 20,7 MPa) šlyties stiprį.

• ✓ Universalūs – įvairioms medžiagoms
• ✓ Tiršti – išlieka tepimo vietoje
• ✓ Strong initial grab
• ✓ Non-toxic
• ✓ Dries to a clear glue line
• ✓ Water clean-up before curing

Bond strength: 210,92 kg/cm²*
Open assembly time: 3-5 min.
Total assembly time: 10-15 min.
Application temperature: above +10 °C.

Versatility and applications. Multi-Surface refers to its suitability for different materials: wood, ceramics, stone, fabric and other porous materials. Suitable for trim, furniture repair and small assembly jobs. At least one side of the joint must be porous.

Preparation and bonding. Surfaces must be clean and dry. Spread the adhesive with the bottle nozzle, a roller or a brush, and join components while the glue is still wet. Hold components firmly together and remove excess before it dries.

Consistency and cleaning. Tiksotropinė, tiršta konsistencija padeda išlaikyti klijus tepimo vietoje. Balti klijai išdžiūvę tampa skaidrūs. Nesukietėjęs perteklius nuvalomas vandeniu ar drėgna šluoste, sukietėjęs – nuskutamas arba nušlifuojamas.

Application limitations. „Titebond Quick & Thick“ skirti vidaus darbams. Nenaudokite lauke ar ten, kur tikėtina didelė drėgmė. Lauko medienos darbams rinkitės pagal paskirtį tinkamus „Titebond II Premium“ arba „Titebond III Ultimate“ klijus. Klijų ir klijuojamų paviršių temperatūra turi būti aukštesnė nei +10 °C. Bent vienas paviršius turi būti porėtas.

Not intended for structural bonding of load-bearing building components. If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.

Storage. Protect from freezing. Check the condition of the glue before use.

Non-toxicity and safe use. „Titebond Quick & Thick“ – netoksiški klijai. Prieš naudodami perskaitykite saugos duomenų lapą ir laikykitės jo nurodymų. Laikykite vaikams nepasiekiamoje vietoje.

*Bond strength measured to ASTM D905, bonding maple to maple at approximately +21 °C: 3000 psi / 20.68 N/mm² / 210.92 kg/cm². Assembly times are given at +21 °C and 50 % relative humidity. Results and working time depend on the materials, surface preparation and bonding conditions.

Naudojimo pavyzdžius rasite skiltyje „Video“, o išsamius techninius duomenis – pridėtame lietuviškame PDF.

Properties and applications

• Specially developed for panel veneering.
• Reduces glue bleed-through through wood veneer.
• Longer time to position veneer and prepare the substrate.
• Uncured glue cleans up with water.

Bonding wood veneer

Spread the adhesive evenly over a flat, clean, porous substrate. Position the veneer and press under the conditions specified in the technical data sheet.

This adhesive is designed for veneering. For general wood assembly, select a wood glue intended for that purpose.

Strength and working conditions

Įspūdingas klijų siūlės stipris – apie 176,3 kg/cm². In the manufacturer's ASTM D905 test on hard maple joints at room temperature, Titebond Cold Press for Veneer achieved a shear strength of 2508 psi (approximately 17.3 MPa).

Atvirasis laikas – apie 15 min., bendras surinkimo laikas – 15-20 min. (+21 °C, 50 % santykinė drėgmė). Dirbkite aukštesnėje nei +10 °C temperatūroje.

Shake the container thoroughly before use to ensure a uniform consistency and viscosity.

Safety and use

No harmful fumes associated with contact adhesives. Titebond Cold Press for Veneer does not emit the harmful or corrosive fumes associated with most contact adhesives. According to the Safety Data Sheet, the mixture is not classified as hazardous. Use as intended and follow the Safety Data Sheet instructions.

Available pack sizes: 948 ml and 3.78 l.

Titebond Multibond EZ-2 – vandeniui atsparūs D3 pramoniniai medienos klijai medinių detalių ir gaminių klijavimui, medžio masyvo sujungimams, dygiavimui ir laminavimui. Vienkomponentė PVA emulsija tinka baldų bei medienos gamybai, kai svarbi šviesi klijų siūlė ir darbas žemesnėje gamybinių patalpų temperatūroje.

Įspūdingas dygiuotų medienos jungčių stipris – apie 450,3 kg/cm². In the manufacturer's ASTM D5572 tensile test on dry Ponderosa pine specimens, the average strength was 6405 psi (approximately 44.2 MPa).

• D3 water resistance
• Single-component PVA adhesive
• For wood finger-jointing and laminating
• Light-coloured glue line

Application and preparation

Prieš darbą gerai išmaišykite. Minimali naudojimo temperatūra – +7 °C. Presavimo režimą parinkite pagal medieną, įrangą ir techninį duomenų lapą.

When should you choose Multibond EZ-2?

This industrial wood adhesive is designed for edge, face and finger-jointed wooden components. Suitable for solid wood assembly and cold-press laminating. The D3 classification helps assess moisture resistance but does not replace the service requirements of the specific product.

How can you achieve a reliable joint?

Components must fit precisely. Wood surfaces must be clean and free from dust and coatings that prevent adhesive penetration. Spread evenly and apply suitable pressure. Colder timber and higher moisture content affect pressing time, so carry out trial bonding before production.

Multibond EZ-2 meets DIN EN 204 D3 and DIN EN 14257 WATT 91 requirements. ASTM D-5572 relates to finger joints in non-structural wood products for dry service conditions. Not intended for bonding load-bearing structures.

Laboratory test data

The tables show test results stated in the previous product description. Assess them in relation to the test method, temperature and materials; the strength of a particular joint depends on bonding conditions.

Titebond Multibond 3215 – pramoniniai D3 medienos klijai lukštui klijuoti, plokštėms laminuoti ir faneruoti. Vienkomponentė PVA emulsija skirta baldų bei medienos gaminių gamybai. Sudėtis padeda riboti klijų prasiskverbimą per lukštą, o klijų likučius nuo presavimo ir suspaudimo įrangos lengviau pašalinti.

Strong glue line for laminating and veneering. The Titebond Multibond 3215 single-component PVA system is designed for veneer, edge and face bonding in cold, hot and radio-frequency presses. Water resistance meets ANSI/HPVA HP-1-2004 Type 2 and WDMA Type 1 and Type 2 requirements. Joint strength depends on the timber, surface preparation and pressing conditions.

• For veneer bonding and veneering
• For hot-press laminating
• Protection against adhesive bleed-through
• Easier equipment cleaning

Application and preparation

Prieš naudojimą išmaišykite. Gamintojo techniniame lape nurodyta minimali naudojimo temperatūra – +16 °C. Tikslų režimą derinkite prie klijuojamų medžiagų.

Adhesive for veneering and laminating

Choose Multibond 3215 for veneer bonding and panel laminating. Suitable for hot pressing and for edge and face bonding in cold and radio-frequency presses. Check suitability for the particular veneer or panel through trial bonding.

What matters when working with thin veneer?

Bleed-through depends on the wood species, veneer thickness, adhesive quantity and pressing conditions. An evenly prepared substrate and controlled application rate help maintain a clean surface. A special additive makes adhesive residue easier to remove from equipment, but regular maintenance is still necessary.

The manufacturer states high water resistance and a formulation with no added formaldehyde. This does not mean it is intended for continuous immersion or load-bearing structures. Check the technical data sheet for full pressing parameters and limitations.

Titebond Multibond SK-8 – ypač stiprūs, vandeniui atsparūs D4 pramoniniai medienos klijai vidaus ir lauko darbams. Vienkomponentė PVA emulsija skirta medžio masyvo sujungimams ir laminavimui. Tinka kietmedžiui, egzotinei medienai, baldų detalėms bei riedlenčių gamybai, taikant tinkamą presavimo technologiją.

Įspūdingas klijų siūlės stipris – apie 304,4 kg/cm². In the manufacturer's ASTM D4317 test on dry maple joints at +24 °C, the average shear strength was 4329 psi (approximately 29.8 MPa).

• D4-class wood adhesive
• For hardwood and exotic timber
• Single-component system
• For laminating and solid wood

Application and preparation

Prieš darbą gerai išmaišykite. Minimali naudojimo temperatūra – +7 °C. Atsparumas drėgmei nepakeičia medienos paviršiaus apsaugos lauko sąlygomis.

Where is Multibond SK-8 used?

Designed for industrial assembly of wood products, edge and face joints, and laminating. The manufacturer highlights skateboard production and cold, hot and radio-frequency pressing. Select suitable surface preparation and pressing conditions for the particular timber and product.

Water resistance and bond strength

SK-8 meets ANSI/HPVA HP-1-2000 Type 1 and ASTM D-4317 Type 1 Wet Use requirements. D4 does not mean unlimited resistance in all outdoor conditions: long-term performance depends on the product's design, timber, protective coating and correct bonding.

Existing laboratory test data are provided below. Assess them alongside the test method and materials rather than as a guaranteed strength for every joint. Read the technical and Safety Data Sheets before use.

Laboratory test data

Results were obtained under the specified test conditions and are not a guarantee for every bonded joint. Joint strength depends on the wood species, surface preparation, adhesive quantity, pressing and temperature.

ASTM D-4317 Type I: test results

Franklin laboratory tests on maple and three-ply birch plywood. Wood failure indicates the percentage of the specimen that failed in the wood rather than along the glue line.