• Extremely fast initial grab on vertical surfaces (5 seconds);
• Maximum initial grab and holding power (a 14 cm bead of adhesive is required for each 1 kg of weight);
• Puikus valdymas – lengva išspausti ir koreguoti iki 10 minučių laikotarpyje;
• Naudojimas bet kokiu oru – neužšąla ir yra atsparūs vandeniui;
• Daugiafunkcinis universalumas – tinka daugeliui statybinių medžiagų, išskyrus nurodytas apribojimuose;
• Very thick (high viscosity);
• In many cases, eliminates the need for nails, screws and other mechanical fixings;
• Pažangi polimerų technologija – nulinis susitraukimas. Išlieka pastoviai lankstūs ir netaps trapūs su amžiumi;
• Reduces installation time and expenditure on fixings;
• Excellent resistance to ageing;
• Application temperature from -18°C to +49°C.

Applications

• Mirrors;
• Mouldings and decorative trim;
• Panels and cladding boards;
• Fireplace trim;
• Bath surround panels and tiles;
• Foam board;
• Vertical shelving;
• Vertical landscaping walls;
• Kitchen wall panels and splashbacks;
• Bonding plasterboard to timber or metal studs;
• Cement boards;
• Concrete, stone;
• Vertical landscaping features;
• Boards and panels;
• Skirting boards;
• Heavy decorative elements.

The manufacturer's comparison leaflet reports the following results for the GREENchoice Water-Based formulation:

• After 1 day: 78,19 kg/cm² (1112,1 psi).
• After 3 days: 80,84 kg/cm² (1149,8 psi).
• Average shear strength after 28 days: 84,64 kg/cm² (1203,9 psi).

The table does not specify the materials bonded or the detailed test conditions. These figures do not guarantee the permissible load for a particular joint. The comparison leaflet is available in the documents section.

Product features

• Profesionalus stiprumas & našumas;
• Water-based;
• VOC-compliant, water-based formulation;
• Suitable for wet and cold timber;
• Water-repellent;
• Creates a strong, secure bond;
• Cleans up easily with water before drying;
• Bonds most building materials;
• For interior and exterior use;

Applications:

• All interior and exterior construction, installation and repair work;
• For all common building and finishing materials
• Bath surround panels and components;
• Cladding boards, wood and plywood;
• Plasterboard, foam board, plastic and bath surrounds;
• Metal;
• Masonry;
• Wet and cold timber;
• And more.

SUITABLE SUBSTRATES:

Dėl tinkamiausio pagrindo kreipkitės į dangų gamintojus ar pardavėjus. Porėti: Betoninės, gerai surištos cementinės grindys, APA grindų fanera (neapdorota) ir šildomos grindys, kurių temperatūra ne aukštesnė kaip 29,4°C (visų sluoksnių). Taip pat gali būti naudojami ant gerai surištų, tinkamai gruntuotų gipso paklotų (tik aukščiausios kokybės). Neporėti: keraminės plytelės, terrazzo plytelės, marmuras, tam tikros epoksidinės dangos ir esamos gerai suklijuotos elastingos grindų dangos. Atkreipkite dėmesį, kad visi pagrindai turi būti tvirti, stabilūs ir gerai suklijuoti.

SUBSTRATE PREPARATION:

All substrates must be clean, dry, structurally sound, properly cured and free from dirt, oil or grease, paint, old adhesive, wax, sealers and curing compounds. Sand away minor unevenness, then vacuum up all loose material. The substrate must be level. Grinding concrete floors is preferable to using filling compounds. Any filling or levelling compounds used must be Portland-cement-based and have a cured compressive strength of at least 3000 psi (210 kg/m²). Moisture levels in concrete floors fluctuate. Choose cementitious materials with the highest possible moisture resistance and consult their manufacturers' application instructions. Weak concrete and all gypsum-based materials require Titebond Concrete Primer or an equivalent before applying adhesive. Acclimatise the flooring and adhesive in the installation room for 72 hours at 15–35 °C (60–95 °F) and 30–65% relative humidity.

MOISTURE AND ALKALINITY TESTING:

Do not use Titebond 780 where moisture or alkalinity limits are exceeded. Do not use when the substrate temperature is below 18°C or above 30°C, or relative humidity exceeds 65%. Concrete must be fully cured for at least 45 days and free from hydrostatic pressure. Titebond 780 must not be applied to sealed slabs or wet, dusty, contaminated or friable substrates. Acclimatise flooring in accordance with its manufacturer's recommendations. Titebond 780 can be used on slabs up to 99% RH and pH 5–8, or 90% RH and pH 5–8 for sheet vinyl. When installing directly onto wooden floors, the floor's moisture content must not exceed 13%.

Product properties and application

„Titebond Melamine Glue“ – klijai medienai, MDF ir medienos drožlių plokštėms su melamino, vinilo ar HPL paviršiais klijuoti. Skirti baldų gamybai ir tiksliam detalių surinkimui. At least one bonding surface must be porous.

Strong initial tack and precise assembly. Grabs quickly, while an open time of approximately 5 minutes allows components to be aligned. The thick consistency reduces runs and drips.

Patikimas melamino ir medienos drožlių plokštės sujungimas – apie 23,8 kg/cm². The manufacturer's ASTM D905 test recorded a strength of 339 psi (approximately 2.34 MPa). This result applies to the melamine-to-particleboard test specimen.

• ✓ For wood, MDF and particleboard
• ✓ For melamine, vinyl and HPL joints
• ✓ Strong initial grab
• ✓ Tiršti – mažiau nubėgimų
• ✓ Dries clear
• ✓ Water clean-up before curing

Shake the container thoroughly before use to ensure a uniform consistency.

Open assembly time: approximately 5 min.
Total assembly time: 10-15 min.
Application temperature: above +5 °C.
Coverage: 5-6 m²/l.

What is this glue designed for? Bonding porous wood, MDF and particleboard to melamine, vinyl or HPL surfaces. Suitable for furniture making, bonding trim and precise assembly.

Consistency and glue-line appearance. Higher viscosity reduces runs and drips. The white glue dries clear.

Application and cleaning. Spread the glue with the bottle nozzle, a roller or a brush. Remove uncured excess with water or a damp cloth. Scrape or sand off cured residue.

Application limitations. For interior use; not intended for outdoor conditions or continuous immersion in water. At least one bonding surface must be porous. Do not use when the glue or bonding surfaces are below +5 °C.

Not intended for structural bonding of load-bearing building components. If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.

Storage and preparation. Protect from freezing. Do not use glue that has frozen and turned into a gel. Shake the container before use to ensure a uniform consistency.

Safe use. Read the product label and current Safety Data Sheet before use, and follow their application and protection requirements. Keep out of children's reach. Contact our technical support if you have questions about application.

Assembly times are given at +21 °C and 50 % relative humidity. Actual working time depends on the materials, temperature, humidity and adhesive layer.

Naudojimo pavyzdžius rasite skiltyje „Video“, o medienos klijų pasirinkimo informaciją – pridėtame lietuviškame kataloge.

Product properties and application

„Titebond Quick & Thick Multi-Surface“ – universalūs, tiršti vandens pagrindo klijai medienai, keramikai, akmeniui, audiniui ir kitoms porėtoms medžiagoms. Skirti vidaus apdailai, baldų remontui ir smulkiems surinkimo darbams. At least one bonding surface must be porous.

Įspūdingas klijų siūlės stipris – apie 210,9 kg/cm². „Titebond Quick & Thick“ gamintojo ASTM D905 bandyme, bandant kietojo klevo jungtis kambario temperatūroje, pasiekė 3000 psi (apie 20,7 MPa) šlyties stiprį.

• ✓ Universalūs – įvairioms medžiagoms
• ✓ Tiršti – išlieka tepimo vietoje
• ✓ Strong initial grab
• ✓ Non-toxic
• ✓ Dries to a clear glue line
• ✓ Water clean-up before curing

Bond strength: 210,92 kg/cm²*
Open assembly time: 3-5 min.
Total assembly time: 10-15 min.
Application temperature: above +10 °C.

Versatility and applications. Multi-Surface refers to its suitability for different materials: wood, ceramics, stone, fabric and other porous materials. Suitable for trim, furniture repair and small assembly jobs. At least one side of the joint must be porous.

Preparation and bonding. Surfaces must be clean and dry. Spread the adhesive with the bottle nozzle, a roller or a brush, and join components while the glue is still wet. Hold components firmly together and remove excess before it dries.

Consistency and cleaning. Tiksotropinė, tiršta konsistencija padeda išlaikyti klijus tepimo vietoje. Balti klijai išdžiūvę tampa skaidrūs. Nesukietėjęs perteklius nuvalomas vandeniu ar drėgna šluoste, sukietėjęs – nuskutamas arba nušlifuojamas.

Application limitations. „Titebond Quick & Thick“ skirti vidaus darbams. Nenaudokite lauke ar ten, kur tikėtina didelė drėgmė. Lauko medienos darbams rinkitės pagal paskirtį tinkamus „Titebond II Premium“ arba „Titebond III Ultimate“ klijus. Klijų ir klijuojamų paviršių temperatūra turi būti aukštesnė nei +10 °C. Bent vienas paviršius turi būti porėtas.

Not intended for structural bonding of load-bearing building components. If proposed for a joint with additional mechanical fixings, the suitability of that arrangement must be assessed by the structural designer.

Storage. Protect from freezing. Check the condition of the glue before use.

Non-toxicity and safe use. „Titebond Quick & Thick“ – netoksiški klijai. Prieš naudodami perskaitykite saugos duomenų lapą ir laikykitės jo nurodymų. Laikykite vaikams nepasiekiamoje vietoje.

*Bond strength measured to ASTM D905, bonding maple to maple at approximately +21 °C: 3000 psi / 20.68 N/mm² / 210.92 kg/cm². Assembly times are given at +21 °C and 50 % relative humidity. Results and working time depend on the materials, surface preparation and bonding conditions.

Naudojimo pavyzdžius rasite skiltyje „Video“, o išsamius techninius duomenis – pridėtame lietuviškame PDF.

Titebond ReacTITE EP-980 – dviejų komponentų EPI klijai SIP skydų ir konstrukcinių izoliacinių plokščių gamybai. Emulsija naudojama su Hardener 200 kietikliu ir įprasta šalto presavimo įranga. Sistema pasižymi ilgu darbo laiku, mažu putojimu bei atsparumu šilumai, vandeniui ir tirpikliams.

• For SIP panel manufacturing
• EPI emulsion with Hardener 200
• Low foaming
• For cold pressing

Application and preparation

Mixing ratio by weight: 100 parts EP-980 emulsion to 15 parts Hardener 200. Weigh components accurately and follow the technical and Safety Data Sheets.

Adhesive system for SIP panels

ReacTITE EP-980 is designed for manufacturing structural insulated panels by bonding the panel facings to the insulation core. The base materials and their combination must suit the manufacturing process. This industrial two-component adhesive is used as a system with Hardener 200; the emulsion alone does not replace the prepared mixture.

Mixing and production control

Calculate component quantities by weight. Do not replace the 100:15 ratio with equal numbers of packs or estimate it by eye. Mix uniformly, apply at the approved spread rate and press according to the panel manufacturing process. Working time depends on temperature and mixture conditions.

The manufacturer references AC05 and ASTM D-7446 standards for SIPs. Final panel compliance also depends on its design, materials and production control. When handling the hardener, follow the protection and ventilation requirements in the Safety Data Sheet.